PCHOME.RO

Collapse

Programare Dragon CAM + Matrix CAM

Collapse
This is a sticky topic.
X
X
Collapse
Currently active users viewing this thread: 1 (0 members and 1 guests)
  • Filter
  • Time
  • Show
Clear All
new posts

    Programare Dragon CAM + Matrix CAM

    Programare Dragon CAM cu ajutorul unui Dragon Loader Card:

    1. Se trece programatorul in Phoenix Mode 6 MHz. Daca se foloseste Infinity USB Phoenix, pe langa cablul USB, se leaga si cablul serial (pin la pin) la COM.
    2. Se deschide programul Dragonload.exe, se introduce Dragonloader Card in programator, se apasa "connect", apoi "programm card" si se alege softul cel mai recent (de ex. Predator3.04.dra). Incarcarea cardului dureaza cateva minute.
    3. Dupa ce s-a programat cardul, se introduce in Dragon CAM, se alege un canal FTA, se merge in menu la "yes, load module" dupa care incepe transferul de soft. Dupa cateva minute apare "loading successful", se scoate loadercard-ul si se reporneste receiverul.
    4. Se scoate berea de la rece.

    #2
    Programare Magic/Matrix cu CAS2:

    1. Deschideti CAS Studio 8.2 Daca totul e ok, va apare in stanga jos seria lui CAS2.
    2. Apasati "CAM Module", faceti click pe Magic (sau Matrix, tot aia e), bagati CAM-ul in slot (acum va apare ce xilinx, flash, etc. aveti pe CAM), apasati "General", apoi "Erase ALL", confirmati ca da si asteptati cam 1 minut sa se stearga.
    3. Cand apare "device erased", apasati "open file", selectati de ex. MRV 2.19 si apasati "write". In cateva minute, programarea este gata. Nu va atingeti de xilinx. Se scoate modulul din CAS2 si se introduce in receiver, preferabil pe un canal FTA.
    4. Se scoate inca o bere de la rece.

    Comment


      #3
      e ceva de neimaginat, chiar deosebit. merci man.

      Comment


        #4
        si citeva Linkuri utile pentru Dragon-CAM
        aici

        lefdata

        CAM HELP CENTER
        dragonCAM Patcher(DCP v0.9)

        Dragon Module.com
        Humax5400Z ToH3.3;Strong SRT6355;Strong4125evolution;
        Vantage VT-X121SCI;PhillipsCryptoworks; DragonCAM;YellowZetaCam; UPC-Direct; PW; Astra/Hotbird/Amos/Sirius

        Comment


          #5
          sal.
          se poate scrie noul predator cu laptopul?mentionez ca am infinity usb,dragon loadercard
          dani29

          Comment


            #6
            Nu! Cu laptopul nu se poate, dar ai tot ce trebuie ca sa-l programezi!

            Comment


              #7
              Kroky felicitari pentru initiativa ta.
              Am in schimb o intrebare: la a 2-a postare ai spus ca se da drumul la programator, se alege apoi o anumita optiune si se introduce CAM-ul in slot; introducerea CAM-ului intr-un slot deja alimentat nu poate determina deteriorarea CAM-ului ( el [CAM] avind si pini de alimentare nu numai de comunicatii date ).

              Comment


                #8
                @bebelus
                Nici o grija, am facut asta de nenumarate ori, atat in CAS2, cat si in receptor si niciodata n-au fost probleme ca l-am introdus intr-un aparat deja alimentat!

                Comment


                  #9
                  Originally posted by Kroky
                  Nu! Cu laptopul nu se poate, dar ai tot ce trebuie ca sa-l programezi!
                  am o rugaminte,ajuta-ma sa-l programez,ce trebuie sa fac?
                  dani29

                  Comment


                    #10
                    You need:
                    -Smartmouse compatible card programmer
                    -The dragonload.exe program
                    or
                    -Fun7 Hex files can be loaded to USB Phoenix or compatible programmer (including programmer without Phoenix capability)
                    (cf ALTERNATIVE METHOD)


                    PHOENIX MODE (6.00 MHZ)
                    ------------
                    -Connect the card programmer to com1 or com2, make sure the programmer is in 6 MHz mode
                    -Execute "dragonload.exe"
                    -By pressing the "Settings" button, you can change from com1 to com2
                    -Press "Connect"
                    -In the file open dialog that appears, select the firmware you want to load.
                    -The card will now be loaded.


                    ALTERNATIVE METHOD (no Phoneix mode needed)
                    ------------------
                    For this method, you need a FUN7 card
                    Using a suitable program, program the FLASH of the FUN7 card with PredatorFun7loader.hex,
                    and program the EEPROMS with JKF_Dragon22X_XXXXXX_FUN7_EEPROM1.hex and JKF_Dragon22X_XXXXXX_FUN7_EEPROM1.hex.
                    Make sure the program you use handle the large eeprom size of the fun7 card correctly!


                    HOW TO UPDATE CAM
                    -----------------
                    Insert the programmed card into the Dragon module. Insert this into a receiver
                    and turn on the receiver. make sure you are tuned to an FTA channel.

                    Go to the Common interface menu on the receiver, and select the "Dragon Loader" module.
                    In the next menu, select "yes, Load module".
                    Now a menu appears indicating that loading is in progress. To see the actual porgress percentage,
                    select "refresh". There is no auto-refresh because some receivers had problems with that....

                    When loading is complete, a menu appears saying "Loading successful". REMOVE the loader
                    card from the module, and switch off and turn back on the receiver.
                    Humax5400Z ToH3.3;Strong SRT6355;Strong4125evolution;
                    Vantage VT-X121SCI;PhillipsCryptoworks; DragonCAM;YellowZetaCam; UPC-Direct; PW; Astra/Hotbird/Amos/Sirius

                    Comment


                      #11
                      @dani29
                      Chiar nu te inteleg, ai exact ce-ti trebuie, ai citit primul post de sus? Faci pas cu pas ce scrie acolo (inclusiv punctul cu berea) si reusesti! Unde te-ai impotmolit?

                      Comment


                        #12
                        ce ai scris sus am inteles ,dar am leptop si as vrea sa-l pun la munca
                        dani29

                        Comment


                          #13
                          Originally posted by dani29
                          ce ai scris sus am inteles ,dar am leptop si as vrea sa-l pun la munca
                          Ce am scris sus ai inteles, dar nu ai inteles ce am scris mai jos: nu se poate cu laptopul! De ce nu pui Infinity USB-ul la treaba?

                          Comment


                            #14
                            Am si eu o intrebare:
                            am un cam mr si am reusit sa-l reprogramez cu laptopu dar doar cu file de mr cand incerc sa pun file de mrev imi da o eroare si nu se face downloadul la fel si cu file de mreborn. Intrebarea este se poate pune file de mrev sau mreborn cu laptopu? daca da, cum? o sa mai pot reveni la file de mr tot cu laptopu?

                            Multumesc anticipat
                            Ofset 32'' moteq sg 2100, invacom quad(lin+cir), pansat 2700, dreambox 500, ss2, Twinhan VP7021,
                            18'' ofset dish + 18'' ofset bev

                            Comment


                              #15
                              Trebuie sa folosesti in primul rand file de MRev de tip .upd, ai asa ceva?

                              Comment



                              Working...
                              X