Register

Welcome to the RDI-Board Community.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.


Donate Now Goal amount for this month: 100 EUR, Received: 100 EUR (100%)
Donate to support this site...

Results 1 to 10 of 10
  1. #1
    Junior Member Friend
    RDI - Board Default Avatar

    Join Date
    Mar 2008
    Location
    Dubai
    Posts
    13
    Posts Thanks / Likes

    Default Error FEAA, need help with EL-700 FTA+ upgrade


    Hi folks!

    Bought this Echolink EL-700 FTA+ in the UAE but I cannot upgrade the software available on the SRS website. Maybe I'm missing a step. It is my first time to do this for this box. I have done other receivers like the TechnoSat 6000plus without any problems.

    I have tried it on a XP and Vista platform with port settings 11500 baud, parity even.

    Used a 9 pin nulmodem cable 2-3, 3-2, 5-5.

    When switching on the receiver, after having started ALIMUPG51, it try to connect to the receiver.

    It says:
    Please power on your STB.
    Open Serial Port..
    Sync to serial port..
    Target not connect or target is error status!

    Then my receiver Errors "FEAA" whatever it means.

    Any suggestions.

    Eddy

  2. #2
    Junior Member Friend
    RDI - Board Default Avatar

    Join Date
    Jun 2007
    Posts
    15
    Posts Thanks / Likes

    Default

    Hi,

    if you don't mind just send me your email address i will send to you the procedure and loader for upgrading of Echolink.

    [email protected]

  3. #3
    Junior Member Friend
    RDI - Board Default Avatar

    Join Date
    Mar 2008
    Location
    Dubai
    Posts
    13
    Posts Thanks / Likes

    Default email send

    have send you an email

  4. #4
    Junior Member Friend
    RDI - Board Default Avatar

    Join Date
    Mar 2008
    Location
    Dubai
    Posts
    13
    Posts Thanks / Likes

    Default current sw

    bootloader 0.9.6
    Maincode 1.3.6
    Cas_data 1.0.0
    defaultdb 1.0.0
    mcu version 1.1.2
    manufact 14C35E
    Product XXA547F41

  5. #5
    Member Mentor
    RDI - Board Default Avatar

    Join Date
    Aug 2004
    Location
    M east
    Posts
    562
    Posts Thanks / Likes

    Default

    Quote Originally Posted by eddy123 View Post
    Hi folks!

    Bought this Echolink EL-700 FTA+ in the UAE but I cannot upgrade the software available on the SRS website. Maybe I'm missing a step. It is my first time to do this for this box. I have done other receivers like the TechnoSat 6000plus without any problems.

    I have tried it on a XP and Vista platform with port settings 11500 baud, parity even.

    Used a 9 pin nulmodem cable 2-3, 3-2, 5-5.

    When switching on the receiver, after having started ALIMUPG51, it try to connect to the receiver.

    It says:
    Please power on your STB.
    Open Serial Port..
    Sync to serial port..
    Target not connect or target is error status!

    Then my receiver Errors "FEAA" whatever it means.

    Any suggestions.

    Eddy
    You can use only ALIMUPG5 loder only and the software only 23 02 08dated pls not use the super software.
    Tech

  6. #6
    Junior Member Friend
    RDI - Board Default Avatar

    Join Date
    Mar 2008
    Location
    Dubai
    Posts
    13
    Posts Thanks / Likes

    Default still doesn't work

    I have tried ALIMUPG version 4 and followed Oto's instructions, version 5 and 5.1 but none is successful. I notice that the software uses port on com 1; with parity even and bit rate 115200. Now by default the port settings are; parity none and bit rate 9600.

    I have changed the port settings to match the software but still no luck. It always errors with FEAA, whatever it means.

    Is my bootloader OK?

    Any other idea's I'm running out.

    Eddy

  7. #7
    Member Mentor
    RDI - Board Default Avatar

    Join Date
    Aug 2004
    Location
    M east
    Posts
    562
    Posts Thanks / Likes

    Default

    Quote Originally Posted by eddy123 View Post
    I have tried ALIMUPG version 4 and followed Oto's instructions, version 5 and 5.1 but none is successful. I notice that the software uses port on com 1; with parity even and bit rate 115200. Now by default the port settings are; parity none and bit rate 9600.

    I have changed the port settings to match the software but still no luck. It always errors with FEAA, whatever it means.

    Is my bootloader OK?

    Any other idea's I'm running out.

    Eddy
    Check ALIMUPG 3 and old software try to load receiver after you can up grade by ALIMUG 5.
    Tech

  8. #8
    Junior Member Friend
    RDI - Board Default Avatar

    Join Date
    Mar 2008
    Location
    Dubai
    Posts
    13
    Posts Thanks / Likes

    Default where to get?

    I have Googled on version 3 but cannot find it. Can you show me where this version can be downloaded?

  9. #9
    Member Mentor
    RDI - Board Default Avatar

    Join Date
    Aug 2004
    Location
    M east
    Posts
    562
    Posts Thanks / Likes

    Default

    Quote Originally Posted by eddy123 View Post
    I have Googled on version 3 but cannot find it. Can you show me where this version can be downloaded?
    If it is not possible you run a diffrent software in this box, try the shope from where you the box they do that, no charge...
    Tech

  10. #10
    aafaqhassan
    Guest
    RDI - Board Default Avatar

    Default Software Problem


    I have digital receiver echolink EL-700 FTA+. Multivision and some
    other packages are not coming for about six days, please send me
    reason and how can I get these channels again?
    My software details are following:

    bootloader 0.9.9
    maincode 1.3.7
    Cas_data 1.0.0
    Default db 1.0.2
    mcu Version 1.12
    manufact 147538
    Product XX3547F41

 

 

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Back to Top