Register

Welcome to the RDI-Board Community.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.


Donate Now Goal amount for this month: 100 EUR, Received: 100 EUR (100%)
Donate to support this site...

Results 1 to 7 of 7
  1. #1
    Junior Member Friend
    RDI - Board Default Avatar

    Join Date
    Jul 2006
    Location
    JEDDAH
    Posts
    17
    Posts Thanks / Likes

    Question Humax 5400z internet sharing


    hi all guys, I have humax IRCI 5400Z.
    1. How i can put Nagra codes for B4UMovies code by remote control.
    2. How i can use it on internet sharing, which softwares needed.
    3. Need a downloader and uploader.
    Thanks for experts for quick response for this new user. Waiting for......

  2. #2
    Junior Member Teacher
    RDI - Board Default Avatar

    Join Date
    Jun 2006
    Posts
    149
    Posts Thanks / Likes

    Default hii

    1. Goto the ToH menu & then Ram editor, enter the B4Umovies keys in the Nagravision section.
    The keys r here http://www.rdi-board.com/showpost.ph...41&postcount=4

    2. For sharing thru internet u need sharemax+SBCL

    3. Use HDFSmart to upload Firmware or Module(s) to your STB.

  3. #3
    Junior Member Friend
    RDI - Board Default Avatar

    Join Date
    Jul 2006
    Location
    JEDDAH
    Posts
    17
    Posts Thanks / Likes

    Default

    hi satpal, thx 4 quick response. but i m sorry i could not upload firmware, it gives message " error ID ". and i put B4Umovies key but it do not open, still scramble. is there any patch ON/OFF code? pls send some text how to use with internet sharing with pc to watch pehla, show time etc. thanks.
    I have ToH 3.3 HoT5.7 already loaded. now i m using Humax loader pack 10 to install firmware ToH3.4 HoT7.9. Where from i can get latest keys and loaders. Thanking in advance. Waiting

  4. #4
    Junior Member Teacher
    RDI - Board Default Avatar

    Join Date
    Jun 2006
    Posts
    149
    Posts Thanks / Likes

    Default

    To be able to enjoy your Humax, you need :

    1) a null modem cable
    2) the Humax Toolbox
    3) the latest Firmware
    4) the latest Settings
    5) the latest PMC Table
    6) the latest Keybin

    Item 1 null modem cable - you have to buy and is very cheap to get
    Items 2 to 6 are luckily always available free on the Web
    To be able to perform items 3 to 6 mentioned above you always need the Humax Toolbox referred to at item 2 above so start by downloading it to your PC

    Then just follow this quide here of how to perform items 3 to 6 successfully starting with item 3 :
    How to upload the latest firmware


    Requirements:-

    Humax Toolbox
    +Cam Firmware Hot Emu xx (with extension HDF) Unzipped File
    Null Modem Cable attached between PC and Receiver

    1. Put Receiver on a FTA Channel and put it in Standby position (ensure to put in ON or STANDBY position always from the Receiver itself and not with Remote)
    2. Connect PC to Receiver with RS 232 Null Modem Cable
    3. From the Humax Toolbox select and start the Humax Uploader Version 2.O Program
    4. Set up the correct Com Port
    5. Click Open File
    6. Double Click on File Name
    7. An Information Screen pops up saying “File is unknown. Install at your own risk”’
    8. Click OK
    9. Click Upload (PC->STB)
    10. Turn On Receiver from Standby position. At this point, a progress bar appears on PC and a simultaneous one on the TV screen
    11. When download is ready, on the TV screen you will see: “End. Press Standby Key”
    12. Press Standby Key.
    13. Then with the Remote select: Menu, Toh, Config (CAID Preselect) and select Card +Emu (vide Note 15 below)
    14. Patch is complete
    15. The following options (found under CAID Preselect) and their meanings are set out below for information and guidance:

    CARD+EMU => For Emulator DEFAULT use + irde*o (2) card (fast zap)
    CARD+EMU+S => For Emulator + Card Sharing (Premiere + ******2)
    CARD+S+EMU => For Emulator + Card Sharing (Premiere + Cryptoworks)
    CARD+S+EMU also support CAM with Conax card in EMU mode (slow zap)
    CAS1 => For Emulatorek/Wallbanger auto switch
    CAS2 => For Nagra Aladin test
    CAS3 => For people with SkyCrypt and Conax supported CAM's
    CAS4 => For people with Nagra supported CAM's or irde*o 2 test
    CAS5 => For Cryptoworks test
    CAS6 => For SHL test

    16. Having done this, you now need to proceed to item 4

    How to upload the latest ChannelList


    1. Save the latest unzipped Settings File in the Folder of your choice
    2. Connect your PC and Receiver by RS- 232C Null Modem Cable
    3. Put your Receiver on a FTA Channel
    4. Open Humax Toolbox
    5. Select the Channel Editor Humbox V 4.1 Program
    6. On the Humbox V 4.1 Program, click on `File` and `Open`
    7. Then select and double-click on the saved unzipped file referred to at 1 above
    8. Your PC screen now displays the details of the new Channel Settings
    9. Go to Edit and Options and select the correct ComPort and Press OK
    10. Go again to Edit and Options, then to Model, type your System ID (if you don’t know or forgot your System ID, with your Remote Control go to Menu, Installation, Status and STB Status and you’ll find it listed there) and press OK
    11. Go to IRD and press on `Download to Humax`
    12. At this stage, a message pops up: Waiting for Humax Connection
    13. Press the Standby button on your Receiver to turn it to On position.
    14. The download starts immediately. Now wait for the ChannelList to be downloaded.
    15. When ready, put Receiver in Standby position
    16. Put Receiver in On position
    17. Now the new ChannelList is downloaded.
    18. Go to Menu, ToH and press on Config, then choose CAID
    Preselect and select Card+Emu

    Next step is to proceed to item 5 - How to upload a PMC Table


    1. Save the latest unzipped PMC Table File in the Folder of your choice
    2. Connect your PC and Receiver by RS- 232C Null Modem Cable
    3. Put your Receiver on a FTA Channel
    4. Open Humax Toolbox
    5. Select the PMC Tool Program
    6. On the PMC Tool Program, click on `File` and `Open`
    7. Then select and double-click on the saved unzipped file referred to at 1 above
    8. Your PC screen now displays the details of the new PMC Table
    9. Go to Config and select the correct Com Port
    10. On the same screen, press STB and Download
    11. At this stage, a message pops up: PC to STB “Waiting for Humax Connection”
    12. Press the Standby button on your Receiver
    13. The download starts immediately. Now wait for the PMC Table to be downloaded to your PC
    14. When ready, put Receiver in Standby position
    15. Put Receiver in On position
    16. Now the new PMC Table is downloaded.
    17. Go to Menu, ToH and press on Config, then choose CAID Preselect and select Card+Emu

    and finally item 6
    Uploading the Key.Bin

    Requirements:

    FunCard inserted in embedded slot of Receiver
    RS-232C Null Modem Cable
    Humax Toolbox
    Latest KeyBin File

    Uploading the Key.Bin

    1. Save the latest unzipped Key.Bin File in the folder of your choice.
    2. Connect your PC with Receiver by RS-232C Null Modem Cable
    3. Start your HumaxReceiver on a FTA Channel
    4. Open Humax Toolbox
    5. From Toolbox, select DRS9500 Emu Ed Ver 4.2 Program
    6. On the Program, go to ? (next to File), Settings and select correct Com Port
    7. Go to File and click `Open File` and then select and double-click on the unzipped Key Bin File referred to at (1) above
    8. Press Write
    9. At this stage, a Message pops up: Do you want to write already loaded file? Yes or No?
    10. Press `Yes`
    11. The download starts immediately and only takes a few seconds to complete.
    12. When download is ready, put Receiver in Standby position (from the Receiver itself)
    13. Put Receiver in On position (again from the Receiver itself)
    14. Go to Menu, ToH and press Config, then choose CAID Preselect and select Card + Emu
    16 Keys are now successfully installed.

  5. #5
    Junior Member Friend
    RDI - Board Default Avatar

    Join Date
    Jul 2006
    Location
    JEDDAH
    Posts
    17
    Posts Thanks / Likes

    Exclamation

    Hi Sir, What a nice explanation,,,, Than u very much. i understood most of it but still a few quries.
    1. what is a fun card? u mean iredeto card
    2. any links 4 Toolbox and latest softwares for downloading

    i hope, after this i will be able to upgrade my humax. it will be a great time 4 me. I request to keep on helping the new guys like me.
    Again thanking a lot.

  6. #6
    Junior Member Teacher
    RDI - Board Default Avatar

    Join Date
    Jun 2006
    Posts
    149
    Posts Thanks / Likes

    Default

    Fun card is a flashable smart card which has a EEPROM in which u can flash the keys and use it in ur STB. Its the same as u r updating ur STB firmware but u need a seprate flashing device to upgrade the funcard. I think the experts can help u more on that.

    For Humax Firmware & tools goto this following site :

    http://www.laurals.com/humax.html

    Regards
    Satpal

  7. #7
    Junior Member Friend
    RDI - Board Default Avatar

    Join Date
    May 2006
    Posts
    10
    Posts Thanks / Likes

    Default


    Quote Originally Posted by satpal123 View Post

    2. For sharing thru internet u need sharemax+SBCL
    Hi satpal123,
    How about question no.2 will you expalain it too?
    I've heard another program using GBox. will you tell us too?

    thanks

 

 

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Back to Top