Welcome to the RDI-Board Community.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.

Donate Now Goal amount for this month: 100 EUR, Received: 10 EUR (10%)
Donate to support this site...

Results 1 to 3 of 3
  1. #1
    Junior Member Friend
    RDI - Board Default Avatar

    Join Date
    Mar 2005
    Posts Thanks / Likes

    Default Question about flash programming

    Dear Friends,

    I am looking for a nice friend who can help me to program digital satellite receivers.

    I have a question about supermax digital receiver?
    Is it possible to program the flash rom of a supermax digital receiver using Jkeys ?

    If yes, please tell me how can i do this?

    Thanks in advance

  2. #2
    Junior Member Teacher
    RDI - Board Default Avatar

    Join Date
    Jan 2004
    Quetta Pakistan
    Posts Thanks / Likes



    Supermax 6000CI

    This receiver has Two kind of Flashes

    1. TE28F800C3TA (8MB)
    2. TE28F160C3TA (16MB)

    Intel Flashes are blocked from pin 13 and 14

    U need to unblock first

    unlock Flashes ....

    As we know only there are two types of locked flashes :
    The first type is hardware lock.
    The second is hardware and software lock

    The Flashes at the below of the picture have the Same pin configurations and same hardware unlock

    Type1 " Harsdware Unlock" :

    Intel : TE28F400B3, 28F800B3, 28F160B3, 28F320B3
    Sharp : LH28F800XXX, LH28F160XXX
    Atmel : AT49BV16x4A(T), AT49BV162A(T)

    Notes :
    1- WP# pin not found in Atmel flashes and Vpp,WP# pins found in the other listed flashes above.
    2- Vpp,WP# pins are Control pins
    3- Verify your computer’s parallel port is set to EPP/ECP in your computer’s BIOS settings. Make note of the parallel port address – it’s usually 378.

    1- In case of Atmel Check if Vpp pin is connected directly to the processor or to the collector of a PNP transistor.
    In case of the others Check if Vpp and WP# pins are connected directly to the processor or to the collector of a PNP transistor.
    2- if connected directly to the processor, cut the line whitch connect them and wire the Vpp (Atmel) ,Vpp and WP# ( the other ) to any 3.3V line.
    if control pins connected to the collector of a PNP transistor connect them directly to any 3.3V line " no need to cut any line" .

    most of receivers have WP# and Vpp pins connected together or WP# connected to 3.3V Vcc " pin 47 on the flash " and Vpp connected to collector of PNP transistor.

    Attach the JTAG parallel plug to your computer’s parallel port.and Power up your receiver.
    4- Start Wall
    a. Click OK through the ID warning box – and ignore the message.
    b. Click Reset uP three times. After each, click OK through the ID warning box.
    c. Leave Wall open on your Windows desktop.
    5- Start jKeys must first recognize the Processor type in the area under “JTAG Info” must read:

    Device ID : 0x1D405041
    Device : STi5518BVC

    6- Select your IRD model.
    7- Click Flash Programming – the programming panel should open right up.
    8- jKeys should recognize the flash type, and open the Programming Panel. If you get an error box about the Mfg or Device ID, then something is wrong. Verify the jKeys.def file is the one
    9- You can erase and program the flash now.
    10- When you finish power-down the IRD and remove all connection.

    Type2 " Harsdware and software Unlock" :

    Intel : TE28F400C3, 28F800C3, 28F160C3, 28F320C3
    ST : M28W800CB , M28W800CT, M28W160CB , M28W160CT

    same as above until step 6

    7- This step sends a command to the processor (Omega) chip to make it cooperate with us and enable flashing.
    Click Development Panel and Ignore the instructions in the box and click OK!

    8- On the left side of the Development Panel, enter:
    Address: 2000E020 (all ‘0’s are zeros)
    Data: 01 Click Write Byte

    9- This step “unlocks” the special locking feature of the Listed flash chips.
    For example if you want to unlock sector 0 SA0 At the address 7FE00000 you must do the following steps:

    With the Development Panel still open enter:
    Address: 7FE00000 (all ‘0’s are zeros)
    Data: 60 (six-zero) Click Write Byte
    Data: D0 (‘D’-zero) Click Write Byte
    Data: FF Click Write Byte

    now SA0 unlocked
    if you need to unlock all sectors you must repeat Step 9 for eatch sector with its Starting address.

    10- close Development Panel
    11- click flash programming and complete the other steps

    __________________________________________________ ____
    This all Information From FANNANSAT TEAM Word by Word

  3. #3
    Platinum member Expert
    Join Date
    Jun 2004
    29°20'N 47°59'E
    Posts Thanks / Likes


    nice tip, we all need this kind of info.



Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

    By thegreat4u2 in forum RDI - English
    Replies: 1
    Last Post: 16th November 2006, 07:51
  2. Replies: 0
    Last Post: 31st May 2006, 21:18
  3. Shadha started regular programming
    By abdulsaboor in forum RDI - English
    Replies: 0
    Last Post: 2nd May 2006, 04:37
  4. help! Topfield: programming an tfd file...?
    By nuclear in forum RDI - English
    Replies: 1
    Last Post: 15th March 2006, 18:46
  5. Opos card programming
    By nasim in forum RDI - English
    Replies: 0
    Last Post: 29th November 2005, 17:35

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Back to Top