Register

Welcome to the RDI-Board Community.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.


Donate Now Goal amount for this month: 100 EUR, Received: 100 EUR (100%)
Donate to support this site...

Page 1 of 82 1231151 ... LastLast
Results 1 to 15 of 1228
  1. #1
    Gold Member Expert
    Join Date
    Mar 2004
    Location
    Lahore
    Posts
    3,718
    Posts Thanks / Likes

    Default Humax IRCI 5400/5400Z Helpline


    The procedure how to upgrade Humax 5400Z IRCI
    1. Install Toolbox into your PC
    2. Download the +CAM firmware: ( HoT emu xx)
    This is the software you have to upload in your receiver in order to have the multi-CAM mode. It’s a file with the extension HDF, and is created by ToH/HoT team.
    3. Prepare for installing :
    3.1. Turn off your Humax (so put it in STAND-BY modus) the card you used up to now it should be in the slot all the time.
    3.2. Connect your PC to the STB using a RS-232C null modem cable
    3.3 Start the Humax Uploader program (HU15.EXE from step 2), and set up the correct COM port and baud rate
    3.4 When you click on humax uploader, 'Open HDF File' choose the HDF file you have downloaded and unzipped at step number 2. An automatic integrity check out is done through the file, next windows should appear if the file it's authentic and OK
    4.Start installation of new firmware:
    4.1 If everything was setup correct, click the 'Upload [PC->STB]' button. You need to turn on the Humax from Stand-by button manually to have the download started. During the process, you should see a progress bar.
    4.2 After 100% a screen opens and tells you to turn on your Humax. The display will show a blinking ‘END’ word. Push the Stand-by button again.
    5.From the receiver remote control, select 'Menu' ->'Config'-> Select Emu or Emu-K instead of Card

    Uploading the Key.Bin

    1. Download the latest key.bin and unzip then in you preferable folder
    2. Start your humax in a channel (preferably FTA channel)
    3. Connect you PC with Humax by RS-232C null modem cable
    4. Open Humax Toolbox, click on DRS9500 EmuEd xx, „ File„ Open File and point to the saved unzipped key bin (see 1). Press open, Write, you’ll see counter reaching 100. After this you restart humax and keys should be stored in the flash now.

    I hope all users of this STB like Kroky,Haq,Gastapoo or other users will co-operate with me to make this thread more useful for newbies like me

    TPS has gone with Humax z
    Fte Max 100S
    Humax IRCI-5400z
    Asiasat 3S,NSS 6,Insat 4B,Thaicom2/5,Intelsat7/10,HB 6/7A/8

  2. #2
    Junior Member Teacher
    Join Date
    Aug 2002
    Location
    pk
    Posts
    113
    Posts Thanks / Likes

    Default salam

    hello mr masood sahib,hope u will be fine and other users.thanks for start new thread for humax.if u need some thing about humax so i am with u.i will exchange any thing which i know (little).




    haq
    be a helping personality

    sorry, if i tell wrong coz i know little

    http://www.tsh-hfd.com

  3. #3
    Platinum member Expert
    Join Date
    Jun 2004
    Location
    29°20'N 47°59'E
    Posts
    5,711
    Posts Thanks / Likes

    Default

    @jogie & Masood,

    it looks funny for both of you to be talking on another forum and post the links of what you discussed, HERE.

  4. #4
    Gold Member Expert
    Join Date
    Mar 2004
    Location
    Lahore
    Posts
    3,718
    Posts Thanks / Likes

    Default

    @boknoy! We are best friends but our choices differs and we love to drag eachother in our respective forums
    @Haq !I need to download new s/w for TPS,,,Ihave downloaded already ToH 3.3 and it doesn't support TPS,,,Polsat AU is working.
    @Jogi ! thanks for link
    Fte Max 100S
    Humax IRCI-5400z
    Asiasat 3S,NSS 6,Insat 4B,Thaicom2/5,Intelsat7/10,HB 6/7A/8

  5. #5
    Junior Member Teacher
    Join Date
    Aug 2002
    Location
    pk
    Posts
    113
    Posts Thanks / Likes

    Default salam

    salam mr masood,pls download 3.3 hot4.0 genuin from toh team instead of any other personlike some arabic guys.after it download fresh key.bin file from mach file section from rdi.use dsr9500 samsung emu4.2.just conect and open file then write when it finish pls reciever off by stanby button on the front of humax .now reciever is ok for tps and others.





    download new compatible pmc file i need.



    haq
    be a helping personality

    sorry, if i tell wrong coz i know little

    http://www.tsh-hfd.com

  6. #6
    Gold Member Expert
    Join Date
    Mar 2004
    Location
    Lahore
    Posts
    3,718
    Posts Thanks / Likes

    Default Re: salam

    Quote Originally Posted by haq
    salam mr masood,pls download 3.3 hot4.0 genuin from toh team instead of any other personlike some arabic guys.after it download fresh key.bin file from mach file section from rdi.use dsr9500 samsung emu4.2.just conect and open file then write when it finish pls reciever off by stanby button on the front of humax .now reciever is ok for tps and others. download new compatible pmc file i need.haq
    salam Mian sahib,,,plz help me to download channel list in my STB.I will have to download one by one SAT's frequencies?
    what is PW to enter in your link?
    Fte Max 100S
    Humax IRCI-5400z
    Asiasat 3S,NSS 6,Insat 4B,Thaicom2/5,Intelsat7/10,HB 6/7A/8

  7. #7
    Gold Member Expert
    Join Date
    Mar 2004
    Location
    Lahore
    Posts
    3,718
    Posts Thanks / Likes

    Default

    I upgraded Humax with ToH 3[1]3 HoT5 official release from http://humax.roliaforum.com/
    I loosed my Hotbird signals whereas C Band singals are ok.
    I tried to downgrade it with old firmware ToH3.3 HoT4.0 but it is being downloaded but not in practical,,,plz help me
    Fte Max 100S
    Humax IRCI-5400z
    Asiasat 3S,NSS 6,Insat 4B,Thaicom2/5,Intelsat7/10,HB 6/7A/8

  8. #8
    Junior Member Teacher
    RDI - Board Default Avatar

    Join Date
    May 2004
    Location
    Kuwait
    Posts
    451
    Posts Thanks / Likes

    Default

    Masood jee change ur antenna settings and u will have the signals...
    To save the Frequency settings use any STB Link or any channel editor to copy it to receiver or from reciver to PC.

    take care.

  9. #9
    Gold Member Expert
    Join Date
    Mar 2004
    Location
    Lahore
    Posts
    3,718
    Posts Thanks / Likes

    Default

    Quote Originally Posted by lovebird
    Masood jee change ur antenna settings and u will have the signals...To save the Frequency settings use any STB Link or any channel editor to copy it to receiver or from reciver to PC.take care.
    I changed the antenna settings alongwith DiSEqC,,but I could get only signals from two dishes

  10. #10
    Junior Member Teacher
    RDI - Board Default Avatar

    Join Date
    May 2004
    Location
    Kuwait
    Posts
    451
    Posts Thanks / Likes

    Default

    Dont use AUTO LNB in ur Antenna setting use port A or B or C according to the satellites it will work....

    take care.

  11. #11
    Junior Member Master
    RDI - Board Default Avatar

    Join Date
    Jul 2004
    Location
    kuwait
    Posts
    54
    Posts Thanks / Likes

    Default TPS not working with new upgrade

    Hi ,
    I tried to upgrade humax 5400z to 4.0,4.3,5.0 with new pmc table (from laural.com site) but xxl , tps not working. What I found is , 7c00 changed to 15000 & there is no key for this. As a result xxl ,TPS not working.

    Then i uploaded old pmc table which has 7c00 code & then xxl, spice working fine but not tps.

    Which version & pmc table should I use.
    Thanx & regards

    with this pmc table

  12. #12
    Gold Member Expert
    Join Date
    Mar 2004
    Location
    Lahore
    Posts
    3,718
    Posts Thanks / Likes

    Default

    New PMC table is uploaded HERE
    How to add new SATs in this BOX..any one knows?
    @lovebird !I will check my LNB if it hasn't fused
    Fte Max 100S
    Humax IRCI-5400z
    Asiasat 3S,NSS 6,Insat 4B,Thaicom2/5,Intelsat7/10,HB 6/7A/8

  13. #13
    Gold Member Expert
    Join Date
    Mar 2004
    Location
    Lahore
    Posts
    3,718
    Posts Thanks / Likes

    Default

    After downloading firmware and PMC table as I try to download the keys thru DSR 9500 EMU Ed42 I receive this message
    "FW checked Failed
    Not valid FW"
    Plz help me

  14. #14
    Junior Member Teacher
    RDI - Board Default Avatar

    Join Date
    Feb 2005
    Posts
    398
    Posts Thanks / Likes

    Default

    Quote Originally Posted by masood
    New PMC table is uploaded HERE
    How to add new SATs in this BOX..any one knows?
    @lovebird !I will check my LNB if it hasn't fused
    You can take a horse to water .......

    Try menu, installation, networks - see the "other" setting? go figure

  15. #15
    Gold Member Expert
    Join Date
    Mar 2004
    Location
    Lahore
    Posts
    3,718
    Posts Thanks / Likes

    Default


    Quote Originally Posted by kuband
    You can take a horse to water .......
    Try menu, installation, networks - see the "other" setting? go figure
    I'm talking about the way how to download Asian SATs thru PC.

 

 

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. HUMAX IRCI 5400Z
    By sali.bangash in forum RDI - English
    Replies: 2
    Last Post: 9th November 2006, 22:02
  2. Cyfra+ fixed on Humax IRCI-5400/5400z
    By masood in forum RDI - English
    Replies: 5
    Last Post: 23rd April 2006, 02:12
  3. Can for Humax IRCI 5400Z
    By bigcharlie in forum RDI - English
    Replies: 1
    Last Post: 26th February 2006, 02:03
  4. HUMAX IRCI 5400Z Help
    By jamshed81 in forum RDI - English
    Replies: 1
    Last Post: 24th September 2005, 14:26
  5. Humax IRCI-5400Z
    By Anonymous in forum SD Receivers
    Replies: 43
    Last Post: 2nd December 2004, 13:25

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Back to Top