Step 1 MultiLoaderCard Xcam / Xcam Premium
Connect Multiloadercard as shown
Step 2
Run MLC Software,select XCAM mode from comboBox,set correct COMPort and click Set Mode button
Step 3
Select XCam TAB

You can select 5 possible option for updating your XCam

Erasing XCAM and putting in Virgin state
Update Boot sector with correct .rom file on Block 0 location by using dedicated button - Load Boot
Update Software ( aplication ) sector with correct .bin file on Block 2 location location by using dedicated button - Load firmware
Update Keys sector with correct .key file on Block 14 location location by using dedicated button - Load keys
Update any file on any sector with correct file on selected block from combo box by using dedicated button - Load .
Please note that this last option can damage your cam if you use it on wrong way ( e.g. if you load firmware (aplication ) on wrong block ( e.g.on Block 0 or Block 14 ).Your cam will be damaged.It's better to use dedicated buttons for boot,firmware and keys.


Erasing XCAM or how to put XCAM in Virgin state

Step 1
Put XCAM in STB and check firmware version
Step 2
Put Loader card into module.
Step 3
Browse thru CAM menu and select Serial Update by clicking OK on remote control BUT only once . On screen will appear ACTIVATE LOADER message.
Step 4
NOW CLICK ERASE ICON ON MLC - Erasing XCAM message will apear on MLC software
Step 5
Confirm, ACTIVATE LOADER in receiver menu by clicking OK button on remote control. On screen you will the following message: UPDATE -PLS WAIT...and MLC will start to erasing XCAM
Step 6
After a while program will finish and you will see XCAM Erased on MLC software.REMOVE CARD FROM MODULE AND RESTART RECEIVER.
Check in receiver module menu status of XCAM.You can see two possible message :
1. XCAM MODULE
2. XCAM MODULE V11
Your XCAM is now in Virgin state


Updating Xcam with bin ( firmware ) files on block 2 from Virgin state

Step 1
Load correct bin files by clicking Load firmware button on main window.MLC will sett block 2 without possibilities to change it.
Step 2
Put Loader card into module. ( Don't put CAM into STB yet )
Step 3
NOW CLICK PROGRAMM ICON ON MLC -Programmin XCAM message will apear on MLC software
Step 4
NOW PUT XCam with Loader card inside ( together) into STB
Step 5
Programming will start on MLC software
Step 6
After a while program will finish and you will see Programming OK on MLC software.REMOVE CARD FROM MODULE AND RESTART RECEIVER.
Check in receiver module menu new version of the software.


Updating Xcam with bin ( firmware ) files on block 2 from Xcrypto menu

Step 1
Put XCAM in STB and check firmware version
Step 2
Put Loader card into module.
Step 3
Browse thru CAM menu and select Serial Update by clicking OK on remote control BUT only once . On screen will appear ACTIVATE LOADER message.
Step 4
NOW CLICK ERASE ICON ON MLC - Erasing XCAM message will apear on MLC software
Step 5
Confirm, ACTIVATE LOADER in receiver menu by clicking OK button on remote control. On screen you will the following message: UPDATE -PLS WAIT...and MLC will start to erasing XCAM
Step 6
After a while program will finish and you will see XCAM Erased on MLC software. RESTART RECEIVER/CAM WITH LOADER CARD INSIDE.
Check in receiver module menu status of XCAM.You can see two possible message :
1. XCAM MODULE
2. XCAM MODULE V11
Your XCAM is now in Virgin state

CONTINUE...

Step 7
Load correct bin files by clicking Load firmware button on main window.MLC will sett block 2 without possibilities to change it.
Step 8
NOW CLICK PROGRAMM ICON ON MLC
Step 9
Programming will start on MLC software
Step 10
After a while program will finish and you will see Programming OK on MLC software.REMOVE CARD FROM MODULE AND RESTART RECEIVER.
Check in receiver module menu new version of the software.

Updating Xcam with key (keys ) files on block 14

Step 1
Load correct key files by clicking Load keys button on main window.MLC will sett block 14 without possibilities to change it.
Step 2
Put XCAM in STB and check firmware version
Step 3
Put Loader card into module.
Step 4
Browse thru CAM menu and select Serial Update by clicking OK on remote control BUT only once . On screen will appear ACTIVATE LOADER message.
Step 5
NOW CLICK PROGRAMM ICON ON MLC - Programmin XCAM message will apear on MLC software
Step 6
Confirm, ACTIVATE LOADER in receiver menu by clicking OK button on remote control. On screen you will the following message: UPDATE -PLS WAIT...and MLC will start to programming XCAM
Step 7
After a while program will finish and you will see XCAM programmed on MLC software.
REMOVE CARD FROM MODULE AND RESTART RECEIVER.
Check in receiver module menu status of XCAM.Browse thru CAM menu and find Settings > Default keys. Click on OK by remote control to activate latest uploaded.


Updating Xcam with rom ( boot ) files on block 0

Warning , never update Xcam with rom files on block 0 if you don't have allready installed Xcrypto aplication on Xcam from 1078 version or above, or if you have Xcam in Virgin mode.

Step 1
Load correct rom files by clicking Load boot button on main window.MLC will sett block 0 without possibilities to change it.
Step 2
Put XCAM in STB and after initialization check software version MUST HAVE XCRYPTO 1078 or ABOVE .IF you don't have it , please STOP any further updating with rom files on block 0 and read how to load firmware first.
Step 3
After confirmation correct version of xcrypto app.put Loader card into module.
Step 4
Browse thru CAM menu and select Serial Update by clicking OK on remote control BUT only once . On screen will appear ACTIVATE LOADER message.
Step 5
NOW CLICK PROGRAM ICON ON MLC - Programming message will apear on MLC software
Step 6
Confirm, ACTIVATE LOADER in receiver menu by clicking OK button on remote control. On screen you will the following message: UPDATE - PLS WAIT...and MLC will start to program XCAM
Step 7
After a while program will finish and you will see Programming OK on MLC software.REMOVE CARD FROM MODULE AND RESTART RECEIVER.
Check in receiver module menu new version of the software. You must have added -p caracter after firmware version.


Updating Xcam with any file on any block ( only for expert )
Please note that this option can damage your cam if you use it on wrong way ( e.g. if you load firmware (aplication ) on wrong block ( e.g.on Block 0 or Block 14 ).Your cam will be damaged.It's better to use dedicated buttons for boot,firmware and keys.

Step 1
Load correct files by clicking Load button at top of MLC software
Step 2
Set desired block from ComboBOX ( WATCH OUT )
Step 3
Put XCAM in STB and check firmware version
Step 4
Put Loader card into module.
Step 5
Browse thru CAM menu and select Serial Update by clicking OK on remote control BUT only once . On screen will appear ACTIVATE LOADER message.
Step 6
NOW CLICK PROGRAMM ICON ON MLC - Programmin XCAM message will apear on MLC software
Step 7
Confirm, ACTIVATE LOADER in receiver menu by clicking OK button on remote control. On screen you will the following message: UPDATE - PLS WAIT...and MLC will start to programming XCAM
Step 8
After a while program will finish and you will see XCAM programmed on MLC software.
REMOVE CARD FROM MODULE AND RESTART RECEIVER.




XCAM BLOCK POSITION

BLOCK 0 is reserved for BOOT.This part is very sensitive and if you damage it by loading bad files on it , your cam will go in neverending initialization.If this happen , XCAM must be opened and repaired.

BLOCK 2 is reseved for Xcrypto application.If you put app_clear file on this block Xcam will enter in Virgin State.Also take care what type of file you're using.Fake file can damage you cam.

BLOCK 14 is reseved for keys files ( softcamkeys ).DON'T put xcrypto application on block 14 becouse you will damage it..If this happen , XCAM must be opened and repaired