Register

Welcome to the RDI-Board Community.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.


Donate Now Goal amount for this month: 100 EUR, Received: 100 EUR (100%)
Donate to support this site...

Results 1 to 6 of 6
  1. #1
    aaroonn
    Guest
    RDI - Board Default Avatar

    Default up grade of micro-x receiver


    hi friends,

    could any one please tell me how to upgarade my 'micro-x 6000ir'
    receiver from computer to receiver...?
    i have down loaded the software from 'astrovax' site - i have 9 pin female to female cord

    how to proceed....?

    thanks in advance

  2. #2
    aaroonn
    Guest
    RDI - Board Default Avatar

    Default

    hey guys

    no one to guide me.......

    still waiting plzzzzzzzzzz

  3. #3
    Junior Member Teacher
    Join Date
    Feb 2005
    Location
    middle-earth
    Posts
    277
    Posts Thanks / Likes

    Default

    Dishman/mysfiles where are you,or other m8 can you help this guy


    helllllllooooooo...

  4. #4
    Junior Member Junior
    RDI - Board Default Avatar

    Join Date
    Dec 2004
    Posts
    5
    Posts Thanks / Likes

    Default

    i dont know much about upgrading, i just hope this can help you.


    SE - THE FILE WITH WORD ZIROG IF YOUR RECEIVER HAS TWO SCART CONNECTORS ON THE BACK PANEL
    USE - THE FILE WITH WORD SHARP IF YOUR RECEIVER HAS ONLT ONE SCART CONNECTOR ON THE BACK PANEL

    After loading the software - go to the key code menu and press the <yellow> key which will
    make the default for the codes.

    Special Codes used to activate key code menu for MIcro-x 2800 - 6000 IR and 6500 IR

    1.To initially activate the key code menu -- one time usage only


    Go to the language setting press <ok> on the remote - highlight <english.
    press <red> key on remote control - followed by 8888

    one additional line will be added -EMULATION ---- you need to "enable" this feature to
    access the code menu. this is a one time activation - please note that incase you download
    new software - by default the EMULATION is set at "disable"

    this feature also can be used as parental control to de -activate the code menu -


    2. To access the key code editing menu --- can be used any time

    Go to the language setting press <ok> on the remote - highlight <english.
    press 9999 on the remote -- the key code menu will appear

    enable the emulation on ----


    3. for receiver to receiver transfer for software.

    Connect slave receiver to the master using a twisted RS-232 cable ( humax or Echostar
    download cable)

    on the master receiver connected to the televsion

    go to "config" in the menu screen then press <ok> --- select system inforamtion then
    press on the remote --- 9999

    select "program code download" press okay

    the transfer progress bar will appear on the screen.


    on completion 100 % disconnect transfer cable and wait for the message 0000 to appear on
    the slave receiver --- very important information or the receiver will mal-function ---


    -naughtypawn-

  5. #5
    Junior Member Junior
    RDI - Board Default Avatar

    Join Date
    Dec 2004
    Posts
    5
    Posts Thanks / Likes

    Default

    -connect your stb to the computer
    -put the power on
    -unzip your file
    -open "DnUpMan'
    -click brows and select your file (zirog or sharp), open it
    -click download beside the version 1.10
    -click start
    -you'll notice your stb is showing 'dnload'
    - wait for the DnUpMan to finish writing
    -if your stb shows the time, that means upgrading is finished
    -follow the instructions to make it your default key

    GOODLUCK


    -naughtypawn-

  6. #6
    aaroonn
    Guest
    RDI - Board Default Avatar

    Default


    thanks guys

    i will try

    do i have to save the existing setting before i upgrade ..?

    thanks again

 

 

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Replies: 2
    Last Post: 19th September 2006, 17:32
  2. Up grade etc
    By malsa in forum RDI - English
    Replies: 9
    Last Post: 22nd August 2006, 22:29
  3. Good news for Astrovox and Micro-x receiver holders
    By scrombi in forum RDI - English
    Replies: 0
    Last Post: 5th January 2006, 08:42
  4. BAN THE ASTROVOX AND MICRO-X RECEIVER
    By santmus in forum RDI - English
    Replies: 1
    Last Post: 1st January 2006, 13:31
  5. micro-x satellite receiver software FOR 4500
    By whoali in forum RDI - English
    Replies: 1
    Last Post: 26th November 2005, 09:31

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Back to Top