Register

Welcome to the RDI-Board Community.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.


Donate Now Goal amount for this month: 100 EUR, Received: 100 EUR (100%)
Donate to support this site...

Results 1 to 11 of 11
  1. #1
    Junior Member Friend
    RDI - Board Default Avatar

    Join Date
    Jun 2006
    Posts
    16
    Posts Thanks / Likes

    Default Oscam/CCcam si HDplus_02 card negru

    Salutare,
    Are cineva un card negru hdplus 02 care merge cu oscam? Am incercat mai multe versiuni de oscam dar nu reuseste sa citeasca cardul. In acelasi slot merge fara probleme cu cccam 2.3.0 sau diablo wifi.
    Ma intereseaza cu oscam sa citesc numai temporar ca sa pot vedea cand expira cardul

    oscam.conf
    [newcamd]
    Key = 0102030405060708091011121314
    Port = [email protected]:003411
    [dvbapi]
    enabled = 1
    au = 1
    boxtype = dreambox
    user = dvbapi
    pmt_mode = 0

    oscam.server
    [reader]
    Label = hdplus
    enable = 1
    Protocol = internal
    Device = /dev/sci0
    Group = 1
    EMMCache = 1,3,2
    n3_rsakey = B..D5
    n3_boxkey = A..C
    mhz = 368
    cardmhz = 368
    nagra_read = 1
    detect = cd
    caid = 1843
    ident = 1843:003411

    oscam.client
    [account]
    User = HDplus
    Pwd = HDpluspass
    Group = 1
    Au = hdplus
    caid = 1843
    ident = 1843:003411

  2. #2
    Junior Member Friend
    RDI - Board Default Avatar

    Join Date
    Jun 2006
    Posts
    16
    Posts Thanks / Likes

    Default

    Iar aici erroarea:
    -------------------------------------------------------------------------------
    >> OSCam << cardserver log switched
    ------------------------------------------------
    ERROR in IO_Serial_Read (errno=11 Resource temporarily unavailable)
    >> OSCam << cardserver log switched, version 1.20-unstable_svn, build #6471 (mips-tuxbox-linux)
    version=1.20-unstable_svn, build #6471, system=mips-tuxbox-linux, nice=-1
    client max. idle=120 sec, debug level=0
    max. logsize=10 Kb, loghistorysize=4096 bytes
    client timeout=5000 ms, fallback timeout=2500 ms, cache delay=120 ms
    ERROR in IO_Serial_Read (errno=11 Resource temporarily unavailable)
    ERROR in IO_Serial_Read (errno=11 Resource temporarily unavailable)
    ERROR in IO_Serial_Read (errno=11 Resource temporarily unavailable)
    card system not supported
    Normal mode failed, reverting to Deprecated Mode
    ERROR in IO_Serial_Read (errno=11 Resource temporarily unavailable)
    ATR: 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50 31 38 30 20 4D 65 72 30 30 30 28
    ERROR in IO_Serial_Read (errno=11 Resource temporarily unavailable)
    Maximum frequency for this card is formally 5 Mhz, clocking it to 3.68 Mhz
    ERROR in IO_Serial_Read (errno=11 Resource temporarily unavailable)
    detect native nagra card
    ERROR in IO_Serial_Read (errno=11 Resource temporarily unavailable)
    ERROR in IO_Serial_Read (errno=11 Resource temporarily unavailable)
    ERROR in IO_Serial_Read (errno=11 Resource temporarily unavailable)
    ERROR in IO_Serial_Read (errno=11 Resource temporarily unavailable)
    ERROR in IO_Serial_Read (errno=11 Resource temporarily unavailable)
    ERROR in IO_Serial_Read (errno=11 Resource temporarily unavailable)
    ERROR in IO_Serial_Read (errno=11 Resource temporarily unavailable)
    ERROR in IO_Serial_Read (errno=11 Resource temporarily unavailable)
    card system not supported
    card initializing error
    init for all local cards done
    anti cascading disabled
    plain dvbapi-client granted (anonymous, au=off)
    dvbapi: 0 entries read from oscam.dvbapi
    dvbapi: [ADD PID 0] CAID: 1830 ECM_PID: 1AEA PROVID: 000000
    dvbapi: [ADD PID 1] CAID: 1843 ECM_PID: 19EA PROVID: 000000
    dvbapi: [ADD PID 2] CAID: 09C4 ECM_PID: 1BEA PROVID: 000000

  3. #3
    Faithful Member Expert
    Join Date
    Sep 2008
    Location
    casa cu flori, strada sperantei, la etaj...
    Posts
    1,361
    Posts Thanks / Likes

    Default

    Da, eu am si e citit cu oscam.

    Atentie
    pune un # in fata la
    #SERIAL READER : /dev/ttyUSB1 smartreader+
    #SMARTCARD CLOCK FREQUENCY: /dev/ttyUSB1
    sau
    #SMARTCARD CLOCK FREQUENCY: /dev/sci0
    din cccam (nu am retinut cu ce reader il citesti)

    Dupa care dai restart la toata sandramaua

    O sa pun si configurile mele
    Do you want to see a picture of a beautiful person? Hold up a mirror...

  4. #4
    Faithful Member Expert
    Join Date
    Sep 2008
    Location
    casa cu flori, strada sperantei, la etaj...
    Posts
    1,361
    Posts Thanks / Likes

    Default

    oscam.server

    Code:
    [reader]
    label = smartreader
    protocol = mouse
    device = /dev/ttyUSB0
    caid = 1843
    rsakey = ..................
    boxkey = .................
    ecmwhitelist = 89
    detect = cd
    mhz = 357
    cardmhz = 357
    ident = 1843:003411,003511
    group = 2
    emmcache = 1,3,2
    blockemm-g = 1
    Atentie la group si reader
    Do you want to see a picture of a beautiful person? Hold up a mirror...

  5. #5
    Junior Member Friend
    RDI - Board Default Avatar

    Join Date
    Jun 2006
    Posts
    16
    Posts Thanks / Likes

    Default

    Mersi @popamare de raspuns.

    Eu folosesc readerul intern /dev/sci0 si dupa merge ok pe cccam 2.3.0 fara nici o setare.

    Aici la oscam:
    2012/03/03 13:38:49 5797A0 r reader hdplus initialized (device=/dev/sci0, detect=cd, mhz=368, cardmhz=36
    2012/03/03 13:38:49 5797A0 r hdplus card detected
    2012/03/03 13:38:56 5797A0 r ERROR in IO_Serial_Read (errno=11 Resource temporarily unavailable)

    Se pare ca Protocol = internal nu ma ajuta sa citesc cardul.

  6. #6
    Junior Member Friend
    RDI - Board Default Avatar

    Join Date
    Jun 2006
    Posts
    16
    Posts Thanks / Likes

    Default

    Am schimbat pe celalalt slot:
    2012/03/03 13:54:40 596880 r reader hdplus initialized (device=/dev/sci1, detect=cd, mhz=368, cardmhz=36
    2012/03/03 13:54:41 596880 r hdplus card detected
    2012/03/03 13:54:46 596880 r ERROR in IO_Serial_Read (errno=11 Resource temporarily unavailable)
    2012/03/03 13:54:46 596880 r ATR: 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50 31 38 30 20 4D 65 72 30 30 30 28
    2012/03/03 13:54:47 596880 r Maximum frequency for this card is formally 5 Mhz, clocking it to 3.68 Mhz
    2012/03/03 13:54:48 596880 r detect native nagra card
    2012/03/03 13:54:53 596880 r ERROR in IO_Serial_Read (errno=11 Resource temporarily unavailable)
    2012/03/03 13:54:58 596880 r ERROR in IO_Serial_Read (errno=11 Resource temporarily unavailable)
    2012/03/03 13:55:02 596880 r ERROR in IO_Serial_Read (errno=11 Resource temporarily unavailable)

    Pentru protocol optiunea internal este corecta:
    http://streamboard.gmc.to/wiki/OSCam...g/oscam.server
    protocol = mouse # (Lokaler Cardreader)
    = internal # (Alle Cardreader mit einem "Device=/dev/sciX")
    = camd35|cs357x # (Cascading - camd 3.5-kompatibler Remote-Server)
    = mp35
    = smartreader
    = serial
    = cs378x
    = gbox
    = newcamd|newcamd525
    = newcamd524
    = cccam
    = radegast
    = pcsc
    = constcw
    = sc8in1 # (SC8in1 und MCR 4/8 Cardreader)

    /tmp# ls -l /dev/sci*
    crw-rw---- 1 root root 10, 56 Jan 1 2000 /dev/sci0
    crw-rw---- 1 root root 10, 55 Jan 1 2000 /dev/sci1

  7. #7
    Junior Member Friend
    RDI - Board Default Avatar

    Join Date
    Jun 2006
    Posts
    16
    Posts Thanks / Likes

    Default

    Probabil este nevoie numai de rabdare. Dupa mai multe restartari a reusit sa vada cardul in slotul /dev/sci1:

    creating thread for device /dev/sci1
    loadbalancer: can't read from file /tmp/.oscam/stat
    waiting for local card init
    reader hdplus initialized (device=/dev/sci1, detect=cd, mhz=368, cardmhz=36
    HTTP Server listening on port 8080
    hdplus card detected
    ERROR in IO_Serial_Read (errno=11 Resource temporarily unavailable)
    ATR: 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50 31 38 30 20 4D 65 72 30 30 30 28
    Maximum frequency for this card is formally 5 Mhz, clocking it to 3.68 Mhz
    detect native nagra card
    [nagra-reader] type: NAGRA, caid: 1843, IRD ID: ..........
    [nagra-reader] ProviderID: 00 00 34 11
    [nagra-reader] active to: 2013/02/24 12:59

    Si ultimul oscam.server folosit:
    [reader]
    Label = hdplus
    enable = 1
    #Protocol = internal
    protocol = internal
    device = /dev/sci1
    #mhz = 600
    #Fallback = 0
    Group = 1
    EMMCache = 1,3,2
    rsakey = .....
    boxkey = .....
    mhz = 368
    cardmhz = 368
    nagra_read = 1
    detect = CD
    caid = 1843
    #ident = 1843:003411
    nice = -1
    WaitForCards = 1
    blockemm-g = 1

  8. #8
    Member Mentor
    RDI - Board Default Avatar

    Join Date
    Nov 2004
    Posts
    531
    Posts Thanks / Likes

    Default

    Ce fel de receiver Dream, Vu+, etc
    Incearca si alt protocol, nu doar newcamd, [cs357x].
    Pe VU+ Uno, cu cateva svn xxxx de oscam am dat de aceeasi problema.

    Bafta

  9. #9
    Moderator Expert
    Join Date
    Apr 2003
    Location
    Wild West
    Posts
    2,529
    Posts Thanks / Likes

    Default

    Quote Originally Posted by skarke67s View Post
    Salutare,
    Are cineva un card negru hdplus 02 care merge cu oscam? Am incercat mai multe versiuni de oscam dar nu reuseste sa citeasca cardul. In acelasi slot merge fara probleme cu cccam 2.3.0 sau diablo wifi.
    Ma intereseaza cu oscam sa citesc numai temporar ca sa pot vedea cand expira cardul

    oscam.conf
    [newcamd]
    Key = 0102030405060708091011121314
    Port = [email protected]:003411
    [dvbapi]
    enabled = 1
    au = 1
    boxtype = dreambox
    user = dvbapi
    pmt_mode = 0

    oscam.server
    [reader]
    Label = hdplus
    enable = 1
    Protocol = internal
    Device = /dev/sci0
    Group = 1
    EMMCache = 1,3,2
    n3_rsakey = B..D5
    n3_boxkey = A..C
    mhz = 368
    cardmhz = 368
    nagra_read = 1
    detect = cd
    caid = 1843
    ident = 1843:003411

    oscam.client
    [account]
    User = HDplus
    Pwd = HDpluspass
    Group = 1
    Au = hdplus
    caid = 1843
    ident = 1843:003411
    Nu mai lua tot felul de tampenii de setari de pe net, incearca sa citesti 5 minute oscam (http://streamboard.gmc.to/wiki/OSCam/en) sa il intelegi si vei vedea ca e floare la ureche setarea oricarui card.

    In setarile tale problemele de citire a cardului sunt la oscam.server ( la mzh = 368 si la cardmhz = 368 ), pune default ( mhz = 357 si cardmhz = 357 ) si la primul reset/reboot oscam va overclocka cardul exact la cat trebuie (asta daca e pe cititorul intern al receptorului sau pe smargo setat pe automatic).
    Setarile le faci doar din interfata daca le faci manual o sa fie o brambureala totala.

  10. #10
    Junior Member Junior
    RDI - Board Default Avatar

    Join Date
    Nov 2010
    Posts
    4
    Posts Thanks / Likes

    Default focus

    Am un server cu Cccam 2.2.1, UPC HU, Canal Digital Nordic si Focus Ro.
    Primele merg fárá problemá, dar Focus nu se updateazá.
    Má poate ajuta cineva?

  11. #11
    Moderator Expert
    Join Date
    Apr 2003
    Location
    Wild West
    Posts
    2,529
    Posts Thanks / Likes

    Default

    Quote Originally Posted by Sztifler0301 View Post
    Am un server cu Cccam 2.2.1, UPC HU, Canal Digital Nordic si Focus Ro.
    Primele merg fárá problemá, dar Focus nu se updateazá.
    Má poate ajuta cineva?
    Pune cardul in oscam sau scam si se updateaza fara probleme.

 

 

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Back to Top