Register

Welcome to the RDI-Board Community.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.


Donate Now Goal amount for this month: 100 EUR, Received: 100 EUR (100%)
Donate to support this site...

Page 1 of 3 123 LastLast
Results 1 to 15 of 44
  1. #1
    Moderator Expert
    Join Date
    Apr 2003
    Location
    Wild West
    Posts
    2,529
    Posts Thanks / Likes

    Default How to CCcam & OsCam pe TOPEX premium (firm koppel) - stick VODAFONE abonament

    Code:
    Instalare firmware :
     - se seteaza reteaua pe pc (ip: 192.168.1.2; gateway: 192.168.1.1)
     - reset hardware: - se apasa buton Reset 30sec ; 
                       - se scoate din priza (mentinut inca 30 sec buton reset), 
                       - se baga din nou in priza (se tine apasat butonul reset 
    				     pana cand se intra in safety mode - ledul PWR clipeste)  
    				   - se incarca noul firmware cu "Firmware Restauration by Asus"
    				   
    Montare stick vodafone (abonament) :
     - se dezactiveaza functia NOCD : 
                       - HyperTerminal :
                                         - AT+ZCDRUN=8      ==> Close autorun state result(0:FAIL 1:SUCCES):1
     - se monteaza in portul usb al routerului :
                       - USB Connection :
                                         - se bifeaza GPRS/EDGE/UMTS
                                             - Username: inernet.vodafone.ro
    										 - Password: vodafone
    										 - APN: internet.vodafone.ro
                                             - Dial Number (usually *99***1#): *99***1#
                                             - USB device serial speed (usually 115200): 921600
                                             - USB device location ID: 1.3
                                             - USB device Vendor ID (0xabcd): 0x19d2
                                             - USB device Product ID (0xefgh): 0x2002
                                             - Modem type: Not Set
    									 - Apply - Finish => save & reboot
    Instalare SSH - IPKG - Optware - CCcam - OsCam : 
    	 - Instalare SSH :
    				   - se partitioneaza un microSD (eu l-am partitionat : 128mb=swap, 512mb=ext3, 1100mb=ext3);
    				   - se introduce in slotul stick-ului de la vodafone;
    				   - instalare propriu-zisa a SSH pe router:
    				     - se intra telnet pe router (user: admin, pass: admin) :
    						 [[email protected] root]$ mkdir -p /usr/local/etc/dropbear
    						 [[email protected] root]$ dropbearkey -t dss -f /usr/local/etc/dropbear/dropbear_dss_host_key
    						 [[email protected] root]$ dropbearkey -t rsa -f /usr/local/etc/dropbear/dropbear_rsa_host_key
    						 [[email protected] root]$ mkdir -p /usr/local/sbin/
    						 [[email protected] root]$ touch /usr/local/sbin/post-boot
    						 [[email protected] root]$ touch /usr/local/sbin/post-firewall
    						 [[email protected] root]$ touch /usr/local/sbin/post-mount
    						 [[email protected] root]$ touch /usr/local/sbin/pre-mount
    						 [[email protected] root]$ touch /usr/local/sbin/pre-shutdown
    						 [[email protected] root]$ chmod +x /usr/local/sbin/*
    						 [[email protected] root]$ echo "#!/bin/sh" >> /usr/local/sbin/post-boot
    						 [[email protected] root]$ echo "dropbear" >> /usr/local/sbin/post-boot
    						 [[email protected] root]$ flashfs save && flashfs commit && flashfs enable && reboot
    						 
    	 - se intra SSH pe router (user: admin, pass: admin):
    					 
    	 - Start swap :
    						 [[email protected] root]$ mkswap /dev/discs/disc0/part1
    						 [[email protected] root]$ swapon /dev/discs/disc0/part1
    						 
    	 - Adaugare fstab :
    					     	 [[email protected] root]$ vi /etc/fstab
    						 [[email protected] root]$ insert
    											/dev/discs/disc0/part1 none swap sw 0 0
    											/dev/discs/disc0/part2 /opt ext3 rw,noatime 1 1
    											/dev/discs/disc0/part2 /mnt ext3 rw,noatime 1 1
    											Salvare script - ESC => :wq => ENTER
    						 
    	 - Salvare fstab :	
    						 [[email protected] root]$ echo "/etc/fstab" >> /usr/local/.filescv
    						 
    	 - Montare usb in startup :
    						 [[email protected] root]$ vi /usr/local/sbin/post-boot
    						 [[email protected] root]$ insert
    											dropbear
    											if [ ! -d /dev/discs ]
    											then
    											insmod scsi_mod && insmod sd_mod && insmod usb-storage && sleep 5s
    											fi
    											mount /dev/discs/disc0/part2 /opt
    											mount /dev/discs/disc0/part3 /tmp/harddisk
    											i=0
    											while [ $i -le 30 ]
    											do
    											if [ -d /opt/etc ]
    											then
    											break
    											fi
    											sleep 1
    											i=`expr $i + 1`
    											done
    											swapon /dev/discs/disc0/part1
    											/opt/cs/cccam/bin/start_CCcam
    											sleep 60
    											/opt/bin/start.sh
    											Salvare script - ESC => :wq => ENTER
    						 [[email protected] root]$ flashfs save && flashfs commit && flashfs enable && reboot
    						 
    	 - Instalare IPKG :
    						 [[email protected] root]$ mkdir /opt/tmp
    						 [[email protected] root]$ mkdir /opt/tmp/ipkg
    						 [[email protected] root]$ ipkg.sh update
    						 [[email protected] root]$ ipkg.sh install ipkg
    						 [[email protected] root]$ ipkg update
    						 [[email protected] root]$ ipkg.sh install ipkg
    						 [[email protected] root]$ ipkg install nano
    						 [[email protected] root]$ flashfs save && flashfs commit && flashfs enable && reboot
    						 
    	 - Instalare Optware :
    						 [[email protected] root]$ wget http://www.3iii.dk/linux/optware/optware-install-ddwrt.sh -O - | tr -d '\r' > /tmp/optware-install.sh
    						 [[email protected] root]$ sh /tmp/optware-install.sh 
    						 
    	 - Instalare libusb :
    						 [[email protected] root]$ remove libiconv 
    						 [[email protected] root]$ ipkg install buildroot make				 
    				   - copiem libusb-1.0.8 in /opt
    						 [[email protected] root]$ cd /opt/libusb-1.0.8
    						 [[email protected] root]$ chmod -R +x *
    						 [[email protected] root]$ ./configure --prefix=/opt
    						 [[email protected] root]$ make && make install	
    							
    	 - Instalare CCcam & OsCam :
    				   - copiem continutul dosarului opt in /opt
    				   
    				    - Instalare CCcam :
    					 - se da atribut 755 fisierelor :
    					                                  - ld.so.1 din /opt
    									      - celor 2 fisiere din /opt/cs/cccam/bin
    									      - tuturor fisierelor din /opt/cs/cccam/lib
    									      - se editeaza restul fisierelor caracteristice cccam din /opt/cs/cccam/etc si /opt/cs/cccam/keys
    										[[email protected] root]$ flashfs save && flashfs commit && flashfs enable && reboot
    													  
    					- Instalare OsCam :
    						 [[email protected] root]$ wget http://oscam.ump2002.net/board/attachment.php?attachmentid=2736
    						 [[email protected] root]$ wget http://oscam.ump2002.net/board/attachment.php?attachmentid=2737
    						 [[email protected] root]$ tar -xvf attachment.php?attachmentid=2736
    						 [[email protected] root]$ tar -xvf attachment.php?attachmentid=2737
    						 [[email protected] root]$ ipkg install pcsc-lite_164_thE29.ipk
    						 [[email protected] root]$ ipkg install ccid_1400_thE29.ipk
    						 [[email protected] root]$ wget http://oscam.ump2002.net/board/attachment.php?attachmentid=1415
    						 [[email protected] root]$ tar -xvf attachment.php?attachmentid=1415
    						 [[email protected] root]$ ipkg install libusb_with_headers_oleg_thE29.ipk
    						 [[email protected] root]$ wget http://oscam.ump2002.net/board/attachment.php?attachmentid=5107
    						 [[email protected] root]$ tar -xvf attachment.php?attachmentid\=5107
    						 [[email protected] root]$ ipkg install oscam-1.00-unstable_svn4395-mon-oleg-thE29.ipk
    						 [[email protected] root]$ mv /opt/bin/oscam /opt/cs/oscam/bin/
    						 [[email protected] root]$ vi /opt/bin/oscam
    												CAMNAME="Oscam Server"
    												CAMDIR="/opt/cs/oscam/bin"
    												CONFDIR="/opt/cs/oscam/conf"
    												LOGDIR="/opt/cs/oscam/log"
    												CAM="oscam"
    												if [ ! -f $CAMDIR/oscam.pid ]
    												then
    												echo "No pidfile exists, Creating PID for oscam"
    												else
    												rm $CAMDIR/oscam.pid
    												echo "Pidfile allready found, Removing old pidfile"
    												fi
    												pidof $CAM > $CAMDIR/oscam.pid
    												PID=$(exec cat $CAMDIR/oscam.pid)
    												start_cam ()
    												{
    												$CAMDIR/$CAM -b -c $CONFDIR &
    												sleep 5
    												}
    												stop_cam ()
    												{
    												kill -9 $PID
    												sleep 5
    												}
    												case "$1" in
    												start)
    												echo "[SCRIPT] $1: $CAMNAME"
    												if ps | grep -v grep | grep -v start | grep $CAM > /dev/null
    												then
    												echo "$CAM runing, stop it first!"
    												else
    												start_cam
    												fi
    												;;
    												stop)
    												echo "[SCRIPT] $1: $CAMNAME"
    												stop_cam
    												;;
    												restart)
    												echo "Restarting $CAMNAME"
    												stop_cam
    												start_cam
    												;;
    												*)
    												"$0" stop
    												exit 1
    												;;
    												esac
    												exit 0
    												Salvare script - ESC => :wq => ENTER
    						 [[email protected] root]$ chmod +x /opt/bin/oscam
    						 [[email protected] root]$ oscam start | restart | stop
    					     	 [[email protected] root]$ vi /opt/bin/start.sh
    												/opt/bin/oscam stop
    												sleep 5
    												/opt/bin/oscam start
    												exit 0 
    												Salvare script - ESC => :wq => ENTER
    						 [[email protected] root]$ chmod +x /opt/bin/start.sh
    						 [[email protected] root]$ flashfs save && flashfs commit && flashfs enable && reboot
    Aveti aici fisierele necesare :
    TOPEX.rar - 7.7 Mb
    pass : ovidiumarius

  2. #2
    Junior Member Teacher
    RDI - Board Default Avatar

    Join Date
    Apr 2006
    Posts
    412
    Posts Thanks / Likes

    Smile Stik vodafone

    Quote Originally Posted by ovidiumarius View Post
    Code:
    Instalare firmware :
     - se seteaza reteaua pe pc (ip: 192.168.1.2; gateway: 192.168.1.1)
     - reset hardware: - se apasa buton Reset 30sec ; 
                       - se scoate din priza (mentinut inca 30 sec buton reset), 
                       - se baga din nou in priza (se tine apasat butonul reset 
    				     pana cand se intra in safety mode - ledul PWR clipeste)  
    				   - se incarca noul firmware cu "Firmware Restauration by Asus"
    				   
    Montare stick vodafone (abonament) :
     - se dezactiveaza functia NOCD : 
                       - HyperTerminal :
                                         - AT+ZCDRUN=8      ==> Close autorun state result(0:FAIL 1:SUCCES):1
     - se monteaza in portul usb al routerului :
                       - USB Connection :
                                         - se bifeaza GPRS/EDGE/UMTS
                                             - Username: inernet.vodafone.ro
    										 - Password: vodafone
    										 - APN: internet.vodafone.ro
                                             - Dial Number (usually *99***1#): *99***1#
                                             - USB device serial speed (usually 115200): 921600
                                             - USB device location ID: 1.3
                                             - USB device Vendor ID (0xabcd): 0x19d2
                                             - USB device Product ID (0xefgh): 0x2002
                                             - Modem type: Not Set
    									 - Apply - Finish => save & reboot
    Instalare SSH - IPKG - Optware - CCcam - OsCam : 
    	 - Instalare SSH :
    				   - se partitioneaza un microSD (eu l-am partitionat : 128mb=swap, 512mb=ext3, 1100mb=ext3);
    				   - se introduce in slotul stick-ului de la vodafone;
    				   - instalare propriu-zisa a SSH pe router:
    				     - se intra telnet pe router (user: admin, pass: admin) :
    						 [[email protected] root]$ mkdir -p /usr/local/etc/dropbear
    						 [[email protected] root]$ dropbearkey -t dss -f /usr/local/etc/dropbear/dropbear_dss_host_key
    						 [[email protected] root]$ dropbearkey -t rsa -f /usr/local/etc/dropbear/dropbear_rsa_host_key
    						 [[email protected] root]$ mkdir -p /usr/local/sbin/
    						 [[email protected] root]$ touch /usr/local/sbin/post-boot
    						 [[email protected] root]$ touch /usr/local/sbin/post-firewall
    						 [[email protected] root]$ touch /usr/local/sbin/post-mount
    						 [[email protected] root]$ touch /usr/local/sbin/pre-mount
    						 [[email protected] root]$ touch /usr/local/sbin/pre-shutdown
    						 [[email protected] root]$ chmod +x /usr/local/sbin/*
    						 [[email protected] root]$ echo "#!/bin/sh" >> /usr/local/sbin/post-boot
    						 [[email protected] root]$ echo "dropbear" >> /usr/local/sbin/post-boot
    						 [[email protected] root]$ flashfs save && flashfs commit && flashfs enable && reboot
    						 
    	 - se intra SSH pe router (user: admin, pass: admin):
    					 
    	 - Start swap :
    						 [[email protected] root]$ mkswap /dev/discs/disc0/part1
    						 [[email protected] root]$ swapon /dev/discs/disc0/part1
    						 
    	 - Adaugare fstab :
    					     	 [[email protected] root]$ vi /etc/fstab
    						 [[email protected] root]$ insert
    											/dev/discs/disc0/part1 none swap sw 0 0
    											/dev/discs/disc0/part2 /opt ext3 rw,noatime 1 1
    											/dev/discs/disc0/part2 /mnt ext3 rw,noatime 1 1
    											Salvare script - ESC => :wq => ENTER
    						 
    	 - Salvare fstab :	
    						 [[email protected] root]$ echo "/etc/fstab" >> /usr/local/.filescv
    						 
    	 - Montare usb in startup :
    						 [[email protected] root]$ vi /usr/local/sbin/post-boot
    						 [[email protected] root]$ insert
    											dropbear
    											if [ ! -d /dev/discs ]
    											then
    											insmod scsi_mod && insmod sd_mod && insmod usb-storage && sleep 5s
    											fi
    											mount /dev/discs/disc0/part2 /opt
    											mount /dev/discs/disc0/part3 /tmp/harddisk
    											i=0
    											while [ $i -le 30 ]
    											do
    											if [ -d /opt/etc ]
    											then
    											break
    											fi
    											sleep 1
    											i=`expr $i + 1`
    											done
    											swapon /dev/discs/disc0/part1
    											/opt/cs/cccam/bin/start_CCcam
    											sleep 60
    											/opt/bin/start.sh
    											Salvare script - ESC => :wq => ENTER
    						 [[email protected] root]$ flashfs save && flashfs commit && flashfs enable && reboot
    						 
    	 - Instalare IPKG :
    						 [[email protected] root]$ mkdir /opt/tmp
    						 [[email protected] root]$ mkdir /opt/tmp/ipkg
    						 [[email protected] root]$ ipkg.sh update
    						 [[email protected] root]$ ipkg.sh install ipkg
    						 [[email protected] root]$ ipkg update
    						 [[email protected] root]$ ipkg.sh install ipkg
    						 [[email protected] root]$ ipkg install nano
    						 [[email protected] root]$ flashfs save && flashfs commit && flashfs enable && reboot
    						 
    	 - Instalare Optware :
    						 [[email protected] root]$ wget http://www.3iii.dk/linux/optware/optware-install-ddwrt.sh -O - | tr -d '\r' > /tmp/optware-install.sh
    						 [[email protected] root]$ sh /tmp/optware-install.sh 
    						 
    	 - Instalare libusb :
    						 [[email protected] root]$ remove libiconv 
    						 [[email protected] root]$ ipkg install buildroot make				 
    				   - copiem libusb-1.0.8 in /opt
    						 [[email protected] root]$ cd /opt/libusb-1.0.8
    						 [[email protected] root]$ chmod -R +x *
    						 [[email protected] root]$ ./configure --prefix=/opt
    						 [[email protected] root]$ make && make install	
    							
    	 - Instalare CCcam & OsCam :
    				   - copiem continutul dosarului opt in /opt
    				   
    				    - Instalare CCcam :
    					 - se da atribut 755 fisierelor :
    					                                  - ld.so.1 din /opt
    									      - celor 2 fisiere din /opt/cs/cccam/bin
    									      - tuturor fisierelor din /opt/cs/cccam/lib
    									      - se editeaza restul fisierelor caracteristice cccam din /opt/cs/cccam/etc si /opt/cs/cccam/keys
    										[[email protected] root]$ flashfs save && flashfs commit && flashfs enable && reboot
    													  
    					- Instalare OsCam :
    						 [[email protected] root]$ wget http://oscam.ump2002.net/board/attachment.php?attachmentid=2736
    						 [[email protected] root]$ wget http://oscam.ump2002.net/board/attachment.php?attachmentid=2737
    						 [[email protected] root]$ tar -xvf attachment.php?attachmentid=2736
    						 [[email protected] root]$ tar -xvf attachment.php?attachmentid=2737
    						 [[email protected] root]$ ipkg install pcsc-lite_164_thE29.ipk
    						 [[email protected] root]$ ipkg install ccid_1400_thE29.ipk
    						 [[email protected] root]$ wget http://oscam.ump2002.net/board/attachment.php?attachmentid=1415
    						 [[email protected] root]$ tar -xvf attachment.php?attachmentid=1415
    						 [[email protected] root]$ ipkg install libusb_with_headers_oleg_thE29.ipk
    						 [[email protected] root]$ wget http://oscam.ump2002.net/board/attachment.php?attachmentid=5107
    						 [[email protected] root]$ tar -xvf attachment.php?attachmentid\=5107
    						 [[email protected] root]$ ipkg install oscam-1.00-unstable_svn4395-mon-oleg-thE29.ipk
    						 [[email protected] root]$ mv /opt/bin/oscam /opt/cs/oscam/bin/
    						 [[email protected] root]$ vi /opt/bin/oscam
    												CAMNAME="Oscam Server"
    												CAMDIR="/opt/cs/oscam/bin"
    												CONFDIR="/opt/cs/oscam/conf"
    												LOGDIR="/opt/cs/oscam/log"
    												CAM="oscam"
    												if [ ! -f $CAMDIR/oscam.pid ]
    												then
    												echo "No pidfile exists, Creating PID for oscam"
    												else
    												rm $CAMDIR/oscam.pid
    												echo "Pidfile allready found, Removing old pidfile"
    												fi
    												pidof $CAM > $CAMDIR/oscam.pid
    												PID=$(exec cat $CAMDIR/oscam.pid)
    												start_cam ()
    												{
    												$CAMDIR/$CAM -b -c $CONFDIR &
    												sleep 5
    												}
    												stop_cam ()
    												{
    												kill -9 $PID
    												sleep 5
    												}
    												case "$1" in
    												start)
    												echo "[SCRIPT] $1: $CAMNAME"
    												if ps | grep -v grep | grep -v start | grep $CAM > /dev/null
    												then
    												echo "$CAM runing, stop it first!"
    												else
    												start_cam
    												fi
    												;;
    												stop)
    												echo "[SCRIPT] $1: $CAMNAME"
    												stop_cam
    												;;
    												restart)
    												echo "Restarting $CAMNAME"
    												stop_cam
    												start_cam
    												;;
    												*)
    												"$0" stop
    												exit 1
    												;;
    												esac
    												exit 0
    												Salvare script - ESC => :wq => ENTER
    						 [[email protected] root]$ chmod +x /opt/bin/oscam
    						 [[email protected] root]$ oscam start | restart | stop
    					     	 [[email protected] root]$ vi /opt/bin/start.sh
    												/opt/bin/oscam stop
    												sleep 5
    												/opt/bin/oscam start
    												exit 0 
    												Salvare script - ESC => :wq => ENTER
    						 [[email protected] root]$ chmod +x /opt/bin/start.sh
    						 [[email protected] root]$ flashfs save && flashfs commit && flashfs enable && reboot
    Aveti aici fisierele necesare :
    TOPEX.rar - 7.7 Mb
    pass : ovidiumarius
    PE DREAMBOX 800-8000 Merge sa faci sharing cu net vodafone (stik usb)?

  3. #3
    Moderator Expert
    Join Date
    Apr 2003
    Location
    Wild West
    Posts
    2,529
    Posts Thanks / Likes

    Default

    Quote Originally Posted by valy_tizu View Post
    PE DREAMBOX 800-8000 Merge sa faci sharing cu net vodafone (stik usb)?
    Ar merge daca ar fi posibilitatea de setare APN.
    Pe dream abia daca merg unele modele de stick wireless AP.

  4. #4
    Junior Member Teacher
    RDI - Board Default Avatar

    Join Date
    Nov 2004
    Location
    Alba Iulia
    Posts
    282
    Posts Thanks / Likes

    Default

    Merge cu orice modem de vodaf?Eu am un 3520-z si nu vrea sa se conecteze cu setarile astea dar nici cu altele ce am incercat eu, cine a reusit cu vodaf pe topex poate ne zice si modelul modemului
    strong 6130, 1,2 al 62E<...>30V / pinacle pctvsat/digi tv(ian`05)

  5. #5
    Moderator Expert
    Join Date
    Apr 2003
    Location
    Wild West
    Posts
    2,529
    Posts Thanks / Likes

    Default

    Facute de mine pe :

    - Vodafone abonament cu modem ZTE 3765-z pe Topex premium :

    Code:
    Modem:
    
    Hyper Terminal
    AT+ZCDRUN=8       ==> Close autorun state result(0:FAIL 1:SUCCES):1
    ###################################################################
    
    Router:
    
    Username: inernet.vodafone.ro
    Password: vodafone
    APN: internet.vodafone.ro
    Dial Number (usually *99***1#): *99***1#
    USB device serial speed (usually 115200): 921600
    USB device location ID: 1.3
    USB device Vendor ID (0xabcd): 0x19d2
    USB device Product ID (0xefgh): 0x2002
    Modem type: Not Set
    ###################################################################
    - Vodafone abonament cu modem ZTE 3765-z pe Topex deluxe :

    Code:
    Modem:
    
    Hyper Terminal
    AT+ZCDRUN=8       ==> Close autorun state result(0:FAIL 1:SUCCES):1
    ###################################################################
    
    Router:
    
    Username: inernet.vodafone.ro
    Password: vodafone
    APN: internet.vodafone.ro
    Dial Number (usually *99***1#): *99***1#
    USB device serial speed (usually 115200): 921600
    USB device location ID: 2.3
    USB device Vendor ID (0xabcd): 0x19d2
    USB device Product ID (0xefgh): 0x2002
    Modem type: Not Set
    ###################################################################
    - Vodafone prepay cu modem HUAWEI 3765 pe topex premium :

    Code:
    Modem:
    
    Hyper Terminal
    AT^U2DIAG=0 dezactivare CDROM       ==> OK
    
    ###################################################################
    
    Router:
    
    Username: tobe.vodafone.ro
    Password: vodafone
    APN: tobe.vodafone.ro
    Dial Number (usually *99***1#): *99***1#
    USB device serial speed (usually 115200): 921600
    USB device location ID: 1.0
    USB device Vendor ID (0xabcd): 0x12d1
    USB device Product ID (0xefgh): 0x1001
    Modem type: Not Set
    ###################################################################
    - RDS cu modem ZTE MF110 pe topex premium :

    Code:
    ###################################################################
    Modem
    
    Hyper Terminal
    AT+ZCDRUN=8       ==> Close autorun state result(0:FAIL 1:SUCCES):1
    ###################################################################
    
    Router:
    
    Username: 
    Password: 
    APN: internet
    Dial Number (usually *99***1#): *99#
    USB device serial speed (usually 115200): 921600
    USB device location ID: 1.2
    USB device Vendor ID (0xabcd): 0x19d2
    USB device Product ID (0xefgh): 0x0016
    Modem type: Not Set
    ###################################################################
    - RDS cu modem ZTE MF110 pe topex deluxe :

    Code:
    Modem:
    
    Hyper Terminal
    AT+ZCDRUN=8       ==> Close autorun state result(0:FAIL 1:SUCCES):1
    ###################################################################
    
    Router:
    
    Username: 
    Password: 
    APN: internet
    Dial Number (usually *99***1#): *99#
    USB device serial speed (usually 115200): 921600
    USB device location ID: 1.2
    USB device Vendor ID (0xabcd): 0x19d2
    USB device Product ID (0xefgh): 0x0016
    Modem type: Not Set
    ###################################################################
    Pentru alte modele daca nu se reuseste cu koppel e indicat a se folosi firmware de aici :

    http://code.google.com/p/wl500g/down...label:Featured

    Aceste imagini suportand aproape toate modelele de stick-uri fara a fi necesar oprirea nocd, setarile pentru sharing fiind identice cu cele din exemplul meu cu firmware koppel.

  6. #6
    Junior Member Teacher
    RDI - Board Default Avatar

    Join Date
    Nov 2004
    Location
    Alba Iulia
    Posts
    282
    Posts Thanks / Likes

    Default

    Ok,am inteles a meu e k3520-z si ma tot chinui cu el nu vrea sa se con,numa palpaie. Pt cei ce nu stiu vendor si id product le gasesc in log ,astea difera de la modem la altu
    strong 6130, 1,2 al 62E<...>30V / pinacle pctvsat/digi tv(ian`05)

  7. #7
    Moderator Expert
    Join Date
    Apr 2003
    Location
    Wild West
    Posts
    2,529
    Posts Thanks / Likes

    Default

    Quote Originally Posted by ionut2 View Post
    Ok,am inteles a meu e k3520-z si ma tot chinui cu el nu vrea sa se con,numa palpaie. Pt cei ce nu stiu vendor si id product le gasesc in log ,astea difera de la modem la altu
    Tu ai citit ce am scris eu mai sus

    Pentru alte modele daca nu se reuseste cu koppel e indicat a se folosi firmware de aici :

    http://code.google.com/p/wl500g/down...label:Featured

    Aceste imagini suportand aproape toate modelele de stick-uri fara a fi necesar oprirea nocd, setarile pentru sharing fiind identice cu cele din exemplul meu cu firmware koppel.

  8. #8
    Junior Member Teacher
    RDI - Board Default Avatar

    Join Date
    Nov 2004
    Location
    Alba Iulia
    Posts
    282
    Posts Thanks / Likes

    Default

    Da,Am softu d wl500g pe el!
    strong 6130, 1,2 al 62E<...>30V / pinacle pctvsat/digi tv(ian`05)

  9. #9
    Senior Member Expert
    Join Date
    Jan 1970
    Location
    S-W RO
    Posts
    1,571
    Posts Thanks / Likes

    Default

    THX @ovidiumarius dar linkul nu e gasit.
    Pls pune inca odata sa incerc si cu softul ala...

  10. #10
    Moderator Expert
    Join Date
    Apr 2003
    Location
    Wild West
    Posts
    2,529
    Posts Thanks / Likes

    Default

    Quote Originally Posted by barghy View Post
    THX @ovidiumarius dar linkul nu e gasit.
    Pls pune inca odata sa incerc si cu softul ala...
    http://code.google.com/p/wl500g/down...label:Featured

  11. #11
    Senior Member Expert
    Join Date
    Jan 1970
    Location
    S-W RO
    Posts
    1,571
    Posts Thanks / Likes

    Default

    THX @ovidiumarius dar tot nu am reusit : am incercat WL500gx-1.9.2.7-d-r2381.trx si WL500gx-1.9.2.7-d-r2624.trx pe Topex Bytton GPRS.
    Nu stiu ce nu fac bine...

  12. #12
    Senior Member Expert
    Join Date
    Apr 2006
    Posts
    1,275
    Posts Thanks / Likes

    Default

    si eu pe Topex Bytton GPRS din 2 bucati doar pe unul a mers sa pun.

  13. #13
    Senior Member Expert
    Join Date
    Feb 2007
    Location
    Prahova
    Posts
    1,162
    Posts Thanks / Likes

    Default

    eu din ce am observat sunt probleme cu firmware de o anumita marime

  14. #14
    Moderator Expert
    Join Date
    Apr 2003
    Location
    Wild West
    Posts
    2,529
    Posts Thanks / Likes

    Default

    Quote Originally Posted by barghy View Post
    THX @ovidiumarius dar tot nu am reusit : am incercat WL500gx-1.9.2.7-d-r2381.trx si WL500gx-1.9.2.7-d-r2624.trx pe Topex Bytton GPRS.
    Nu stiu ce nu fac bine...
    Cu aceste firmware merge fara probleme orice Topex Bytton GPRS.
    Pentru a recunoaste si a fucntiona ok stick-ul e nevoie sa setezi exact usb-ul pe care e montat, aici intervenind o chichita si anume : daca gresesti numarul usb-ului e nevoie ca dupa ce pui nuymarul altui usb sa se opreasca de tot routerul inainte de a fi pornit din nou.
    Acesta setare o faci din incercari pana gasesti exact locatia unde se instaleaza stick-ul.

    P.S: versiunea .gx e pentru topex deluxe.

  15. #15
    Junior Member Master
    Join Date
    Jan 2004
    Posts
    75
    Posts Thanks / Likes

    Default Boot

    Se poate modifica sa booteze de pe stick? Am un WL520GU, cu 4 MB flash si 16 MB RAM.
    Am instalat firmware pentru acest model din linkul de mai sus si inainte de instalare Optware am deja cam putina memorie libera, nu am mai continuat:
    [[email protected] root]$ free
    total used free shared buffers
    Mem: 13844 13472 372 0 3308
    -/+ buffers: 10164 3680
    Swap: 126812 64 126748
    [[email protected] root]$
    [[email protected] root]$
    .
    Mai am o intrebare: se poate instala Phoenix cu convertor USB-serial?
    Offset 1.2 Al + HH Strong2100; SS2 ; DM 500S; Nokia Dbox2 2*I; Offset 0.9 DigiTV 2 x HSS-1160NA; clona 800HD, Yamaha TDM850.

 

 

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Back to Top